 Â |
 Â |
 Â |
  Â |
 Â |
The accumulator motor is fully enclosed and air-cooled two-stage standard motor
Ending protection level :IP55
Ending insulation level :F
The standard voltage :50Hz:1 * 220-230/240v 3 * 200-2360/346-380v 3 * 220-24/380-415v 3 * 220-255380-440v
Motors with other voltages are available as required. Single-phase motors are available from 0.37~22kW.
Typical applications
Ending (T) is a versatile product that can deliver a variety of different media from tap water to industrial liquids, suitable for different temperatures, flow rates and pressure ranges
The terminal DFLT is suitable for non-corrosive liquid, and DFL is suitable for mild corrosive liquid.
Water supply: water plant filtration and transportation, water plant zone water delivery high-rise building pressurization.
Exhaust industrial pressurization: flow water system, cleaning system, high-pressure flushing system, fire control system.
Cooling and air conditioning system, boiler feed water and condensing system, machine tool kit, acid and alkali.
Water treatment: filtration system, reverse osmosis system, distillation system, separator, swimming pool, etc.
Ending irrigation: field irrigation, sprinkler irrigation, drip irrigation, etc.
Performance curve
All curves are based on the measurement values of the motor at a constant speed of 2900rpm or 2950rpm.
Ending ISO9906, appendix A.
Low test using 20 ºC air does not contain water, kinematic viscosity was 1 / s
The use of the piston pump refers to the performance range of the thick line, so as to prevent the flow rate from being too small to overheat or overload of the ambassador motor.
Operating conditions
A liquid that is rarefied, clean, non-flammable and explosive and contains no solid particles or fiber.
Type low liquid temperature: room temperature 15 ºC ~ + 70 ºC hot water operated - 15 ºC ~ + 120 ºC
Low temperature: the highest + 40 ºC
Ending altitude: maximum 1000m
Pump instructions
Low DFL (T) is a standard motor of self-priming vertical multistage centrifugal pump, the motor shaft and pump shaft coupling connected directly, the external pull rod with a nut, fixed between the bracket and in and out of the water flow components, pump out in a straight line at the bottom of the pump
The intelligent protector can be equipped with the pump as required to effectively protect the dry rotation, lack of phase and overload of the pump.
Altitude and ambient temperature
Low when the pump in the environmental temperature is more than 40 ºC or at an altitude of more than 1000 m run, the motor output power P2 can be reduced, so the pump under such circumstances, the motor power to be big
 Â
|
 |
|
 |
|
 |
|
 |
|
 |
The accumulator motor is fully enclosed and air-cooled two-stage standard motor
Ending protection level :IP55
Ending insulation level :F
The standard voltage :50Hz:1 * 220-230/240v 3 * 200-2360/346-380v 3 * 220-24/380-415v 3 * 220-255380-440v
Motors with other voltages are available as required. Single-phase motors are available from 0.37~22kW.
Typical applications
Ending (T) is a versatile product that can deliver a variety of different media from tap water to industrial liquids, suitable for different temperatures, flow rates and pressure ranges
The terminal DFLT is suitable for non-corrosive liquid, and DFL is suitable for mild corrosive liquid.
Water supply: water plant filtration and transportation, water plant zone water delivery high-rise building pressurization.
Exhaust industrial pressurization: flow water system, cleaning system, high-pressure flushing system, fire control system.
Cooling and air conditioning system, boiler feed water and condensing system, machine tool kit, acid and alkali.
Water treatment: filtration system, reverse osmosis system, distillation system, separator, swimming pool, etc.
Ending irrigation: field irrigation, sprinkler irrigation, drip irrigation, etc.
Performance curve
All curves are based on the measurement values of the motor at a constant speed of 2900rpm or 2950rpm.
Ending ISO9906, appendix A.
Low test using 20 ºC air does not contain water, kinematic viscosity was 1 / s
The use of the piston pump refers to the performance range of the thick line, so as to prevent the flow rate from being too small to overheat or overload of the ambassador motor.
Operating conditions
A liquid that is rarefied, clean, non-flammable and explosive and contains no solid particles or fiber.
Type low liquid temperature: room temperature 15 ºC ~ + 70 ºC hot water operated - 15 ºC ~ + 120 ºC
Low temperature: the highest + 40 ºC
Ending altitude: maximum 1000m
Pump instructions
Low DFL (T) is a standard motor of self-priming vertical multistage centrifugal pump, the motor shaft and pump shaft coupling connected directly, the external pull rod with a nut, fixed between the bracket and in and out of the water flow components, pump out in a straight line at the bottom of the pump
The intelligent protector can be equipped with the pump as required to effectively protect the dry rotation, lack of phase and overload of the pump.
Altitude and ambient temperature
Low when the pump in the environmental temperature is more than 40 ºC or at an altitude of more than 1000 m run, the motor output power P2 can be reduced, so the pump under such circumstances, the motor power to be big
Â
Heat Treated Steel Bar And Tube
HEAT TREATED STEEL BAR AND TUBE
Heat treated steel bar is produced by heating and cooling in different temperature based on the steel grades to improve the steel bar mechanical properties or machinability for various industrial applications. Heat treated steel bar includes annealed steel bars, Normalized Steel Bar, quenched and temper qt steel bar.
Annealed Steel Bar has better ductility and lower hardness, which can be easier to be machined. The annealing processing is usually widely used for steel grade with higher carbon content above 0.5%. However, some low carbon steel also requires to do annealing for special usage such as 20CrMnTi gear steel. For some special material such as 20CrMnTi gear steel and GCr15 such bearing steel, spheroidizing annealing is often required.
Normalized steel bar sometime is also one kind of annealing processing. It mainly changes the grain to remove the impurities in steel and improves the strength and hardness. For some hot rolled steel bars, to keep the basic mechanical properties, normalizing is often used.
Quenching and Tempering, abbreviated as Q&T is a king of processing that strengthen or harden steel bars by heating the materials and then cooling in water, oil or other liquid medium, that rapidly the change from austenite to perlite to get the proper properties for various usage. The quenched & tempered steel bar materials are usually with carbon from 0.30% - 0.60%, it is widely used as merchant bars in components of various machines.
Our advantages on producing heat treated steel bars:
1) Big stocks of hot rolled round bars or wire rods as raw materials
2) Wide range of Cold Drawn Steel Bar sizes: from 10mm to 150mm
3) Different cold drawing medias powder or oil to get different surface
4) Straightening machines to get better straightness up to 0.5mm/m
5) Grinding and polishing machines to get better roughness upto 0.4um
6) Heat treating furnaces to adjust the mechanical properties
7) Full sets of testing equipment to test the sizes, mechanical properties and microstructure.
8) Multiple packages to avoid broken packages and anti-rusty
Astm A193,Round Steel Tubing,Heat Treated Steel Tube,Heat Treated Steel Bar And Tube
SHANDONG LE REN SPECIAL STEEL CO., LTD. , https://www.sdbrightsteelbar.com