1. Measuring range: Frequency: 10 ~ 300Hz
Amplitude: 0 to 200um 0 to 500um 0 to 800um (peak to peak)
Intensity: 0 ~ 20mm / s 0 ~ 25mm / s 0 ~ 50mm / s (true RMS)
2. Measurement accuracy: ±0.5, linear error ≤1%FS
3. Measurement method: vertical or horizontal
4. Output signal: current output: 4 ~ 20mA (load ≤ 1KΩ)
5. Ambient temperature: -10 ~ 65 ° C (relative humidity ≤ 85%)
6. Power supply voltage: DC24V (power consumption ≤ 3W)
7. Dimensions: 35 × 75 (mm)
8. Fixed screw hole: M10×1.5×10mm
ST-2G vibration sensor sensitivity 20-50mv/mms
Second, the basic principles
The basic principle of the CD-21 series speed sensor is based on an inertial mass (coil assembly) and a housing in which a magnet is fixed. When the inertial mass is suspended from the housing by the elastic element, the sensor housing is fixed to the vibrating body. Above, this
SG-2 Vibration Speed ​​Sensor The vibration speed sensor is usually used to measure the vibration of the bearing and, in a few cases, to measure the vibration of the shaft. When measuring the vibration speed, if the sensor is installed incorrectly or the installation is not strong, the measurement result may be distorted or the sensor may be damaged due to vibration. Therefore, we must carefully choose the installation method of the vibration speed sensor. The vibration sensor is used together with the vibration monitor to achieve continuous long-term monitoring and is suitable for measurement of mechanical vibrations such as steam turbines, fans, pumps, and coal mills. The working principle is based on a primary component that converts mechanical energy into electrical energy. It is fixed on the bracket by two coils, and a piece of magnetic steel is connected to the casing through the piece, and the magnetic steel moves in the line. The magnetic lines of force are cut, thus generating an induced electromotive force. The voltage is proportional to the speed of the casing, which is called the vibration speed sensor. The vibration sensor produced by Zhengzhou Hangke has small volume, good sealing and long service life. Due to the double coil structure, it can superimpose the effective signals, and the interference signal attenuation effectively improves the anti-interference ability.
SG-2 vibration speed sensor SDJ-2G-2S
Integrated vibration and temperature transmitter KL-ZDW86-60-A
Integrated vibration and temperature transmitter KL-ZDW86-40-A
HZD-L-A2-B2-C2-D2-E2 vibration intensity monitoring and protection device
TRA-2X intelligent travel monitoring and protection device
Thermal expansion monitor ZT6501
Vibration Monitoring and Protection Instrument SDJ-3B
Vibration monitoring and protection device HZD-D/S-2
SDJ-3BS, SDJ-3LS type vibration monitoring and protection device
SDJ-6N vibration monitoring and protection instrument (intelligent)
SDJ-6L vibration monitoring and protection device
SDJ-3L vibration monitoring and protection device
CDX-2 vibration monitor
CDX-2A vibration intensity monitor
ZDX-N type shaft vibration monitor
XDZW-2 axial displacement monitoring and protection device
XDZC-2 type expansion monitoring and protection device
YDJ-A oil motive monitor
YDJ-Y type fuel tank oil level monitoring and protection device
Sheet Metal Fabrication Service
Processing steps For Sheet Metal Parts - Custom Sheet Metal Fabrication Service Company
1. Design and draw the part drawing of its sheet metal parts, also known as three views. Its function is to express the structure of its sheet metal parts by means of drawings.
2. Draw an unfolded drawing. That is, unfold a part with a complicated structure into a flat piece.
3. Unloading. There are many ways to unload, mainly the following methods:
a. Shearing machine cuts the material. It uses the shearing machine to cut out the length and width dimensions of the expanded drawing. If there are punching and corner cutting, then the punching machine is combined with the die to punch and corner to form.
b. Punch blanking. It is the use of a punch to punch the structure of the flat part after the parts are unfolded on the plate in one or more steps. Its advantages are short labor hours, high efficiency, and can reduce processing costs. It is often used in mass production.
c. NC CNC blanking. When NC blanking, you must first write a Cnc Machining program. That is, use the programming software to write the drawn expanded diagram into a program that can be recognized by the NC CNC machining machine. Let it follow these programs step by step on a piece of iron plate On the top,punch out the structural shape of its flat parts.
d. Laser cutting is the use of laser cutting to cut the structure and shape of the flat piece on an iron plate.
4. Flanging and tapping. Flanging is also called hole extraction, which is to draw a slightly larger hole on a smaller base hole, and then tap the hole. This can increase its strength and avoid slippage. Generally used for sheet metal processing with relatively thin plate thickness. When the plate thickness is large, such as the plate thickness of 2.0, 2.5, etc., we can tap directly without flanging.
5. Punch processing. Generally, punch processing includes punching and cutting corners, punching blanking, punching convex hull, punching and tearing, punching and other processing methods to achieve processing purposes. Its processing requires corresponding molds to complete the operation. There are convex molds for punching convex hulls, and tearing forming molds for punching and tearing.
6. Pressure riveting. As far as our factory is concerned, pressure riveting studs, pressure riveting nuts, pressure riveting screws, etc. are often used. The pressure riveting method is generally completed by a punch or hydraulic pressure riveting machine. Riveted to the sheet metal part.
7. Bending. Bending is to fold 2D flat parts into 3D parts. Its processing requires a folding bed and corresponding bending molds to complete the operation. It also has a certain bending sequence, and the principle is to make the next cut The first fold that does not cause interference will produce the interference back fold.
8. Welding. Welding is the group welding of multiple parts together to achieve the purpose of processing or the edge welding of a single part to increase its strength. The processing parties generally include the following: CO2 gas shielded welding, argon arc welding, Spot welding, robot welding, etc. The selection of these welding methods is based on actual requirements and materials. Generally speaking, CO2 gas shielded welding is used for iron plate welding; argon arc welding is used for aluminum plate welding; robot welding is mainly in-material It is used when the parts are large and the welding seam is long. Such as cabinet welding, robot welding can be used, which can save a lot of tasks and improve work efficiency and welding quality.
9. Surface treatment. Surface treatment generally includes phosphating film, electroplating colorful zinc, chromate, baking varnish, oxidation, etc. Phosphating film is generally used for cold-rolled plates and electrolytic plates, and its function is mainly to plate on the surface of the material. A protective film is applied to prevent oxidation; the second is to enhance the adhesion of its baking paint. Electroplated multicolored zinc is generally treated with cold-rolled plate surface treatment; chromate and oxidation are generally used for surface treatment of aluminum plates and aluminum profiles; its specific surface The choice of treatment method is based on the customer's requirements.
10. Assembly. The so-called assembly is to group multiple parts or components together in a certain way to make them into a complete material. One thing that needs to be paid attention to is the protection of the materials, and no scratches. Assembly is the last step in the completion of a material. If the material cannot be used due to scratches, it needs to be reworked and reworked, which will waste a lot of processing man-hours and increase The cost of the item. So pay special attention to the protection of the item.
Sheet Metal Fabrication Service,Galvanized Sheet Fabrication Service,Custom Machining Service ,Cnc Stainless Steel Machining
Ningbo Rongna Technology Co.,Ltd , https://www.service-machining.com